濟南膩子粉使用不翻車！調制+施工全流程技巧大揭秘

　　Jinan putty powder does not overturn when used! Unveiling the full process techniques of modulation and construction

　　裝修時，墻面批刮膩子的效果直接決定后續顏值和耐用性。很多人墻面出現開裂、脫落、起砂等問題，根源要么是膩子調制不到位，要么是施工流程偷了步。今天就把膩子粉從調制到施工的核心技巧講透，都是實操中總結的干貨，不管是自己動手還是監督工人，照著做就能讓墻面平整又耐用。

　　When decorating, the effect of wall putty directly determines the subsequent appearance and durability. Many people experience problems such as cracking, peeling, and sanding on their walls, either due to inadequate putty preparation or a flawed construction process. Today, we will explain the core techniques of putty powder from preparation to construction, which are all practical knowledge. Whether you do it yourself or supervise workers, following them can make the wall flat and durable.

　　先說說最基礎也最關鍵的膩子調制環節，這步沒做好，后續再怎么補救都難。首先配比要精準，千萬別憑感覺加水。正規膩子粉包裝上都會標注粉水比例，通常是2:1左右，一定要嚴格按照說明來，而且要分次加水攪拌。加水太多會讓膩子過稀，后期干燥時容易收縮開裂；加水太少則會導致膩子過干，不僅難以批刮平整，附著力還特別差，用不了多久就會起皮脫落。

　　First, let's talk about the most basic and critical step of putty mixing. If this step is not done well, it will be difficult to remedy it in the future. Firstly, the ratio should be precise, and do not add water based on intuition. The packaging of regular putty powder will indicate the ratio of powder to water, usually around 2:1. It is necessary to strictly follow the instructions and add water in batches for mixing. Adding too much water will make the putty too thin, and it is easy to shrink and crack when it dries later; Adding too little water can cause the putty to become too dry, making it difficult to apply and smooth. The adhesion is also particularly poor, and it will peel off after a short period of time.

　　攪拌環節也不能馬虎，建議用電動攪拌器，手動攪拌很難達到均勻效果。要把膩子粉攪拌成沒有顆粒、質地細膩的膏狀，攪拌完成后別著急用，靜置5-10分鐘“醒粉”很重要。這一步能讓水分和粉料充分融合，讓膩子的粘性更好，后續批刮時也更順滑。醒粉后再進行二次攪拌，確保沒有沉淀和結塊，這樣的膩子才能保證施工效果。

　　The mixing process should not be careless. It is recommended to use an electric mixer, as manual mixing is difficult to achieve uniform results. It is important to mix the putty powder into a paste without particles and with a fine texture. After mixing, do not use it urgently and let it sit for 5-10 minutes to "wake up the powder". This step allows for the full integration of moisture and powder, resulting in better adhesion of the putty and smoother subsequent scraping. After waking up the powder, stir it again to ensure that there is no sedimentation or agglomeration, so that the putty can ensure the construction effect.

　　還有個容易被忽略的細節是水溫，調制膩子一定要用常溫清水。用冰水或熱水都會影響膩子粉里膠凝材料的活性，導致膩子凝固不均勻，干固后強度不足，后期容易出現粉化、脫落的問題。另外，要根據施工量少量多次調制，調好的膩子最好在2小時內用完。放置時間太久會讓膩子變干結塊，就算強行加水攪拌，也會破壞其原有性能，用在墻面上容易起砂，影響整體質量。

　　Another easily overlooked detail is the water temperature. When preparing putty, it is necessary to use room temperature water. Using ice water or hot water can affect the activity of the cementitious material in the putty powder, resulting in uneven solidification of the putty, insufficient strength after drying, and easy powdering and peeling problems in the later stage. In addition, it is necessary to mix the putty in small quantities multiple times according to the construction volume, and the mixed putty should be used up within 2 hours. Leaving it for too long can cause the putty to dry and clump, and even if it is forcibly mixed with water, it will damage its original performance. When used on walls, it is prone to sanding, affecting the overall quality.

　　調制好膩子，接下來就是施工流程，每一步都不能省。第一步基層處理是關鍵中的關鍵，很多墻面問題都出在這。先把墻面的浮灰、油污徹底清理干凈，再檢查墻面，空鼓、起皮的地方要全部鏟掉；墻面有裂縫的話，先用嵌縫石膏填補，再貼上網格布加固，防止后期裂縫擴大；最后整體刷一遍界面劑，它能增強膩子和墻面的附著力，從根源避免膩子脫落。

　　After preparing the putty, the next step is the construction process, and every step cannot be skipped. The first step of grassroots treatment is crucial, as many wall problems arise here. First, thoroughly clean the floating dust and oil stains on the wall, and then inspect the wall. Any hollowing or peeling areas should be completely removed; If there are cracks on the wall, fill them with joint gypsum first, and then reinforce them with mesh cloth to prevent the cracks from expanding in the later stage; Finally, brush the interface agent once as a whole, which can enhance the adhesion between the putty and the wall, and prevent the putty from falling off from the root.

　　基層處理好后就可以批刮膩子了，通常需要批刮兩遍。第一遍重點是“找平”，不用追求過度光滑，把墻面的高低起伏填補平整就行，厚度控制在2-3毫米比較合適。刮完后讓墻面自然干燥，具體時間看環境濕度，一般1-2天就能干透，一定要等第一遍完全干透再刮第二遍，不然兩層膩子容易粘連不牢。第二遍的重點是“找細”，要把第一遍留下的小瑕疵、劃痕都填補好，讓墻面整體平整光滑。

　　After the grassroots treatment is completed, putty can be applied, usually requiring two coats of application. The key point of the first round is "leveling", there is no need to pursue excessive smoothness, just fill in the ups and downs of the wall and make it flat, and the thickness should be controlled at 2-3 millimeters, which is more suitable. After scraping, let the wall dry naturally. The specific time depends on the humidity of the environment. Generally, it can dry completely in 1-2 days. It is necessary to wait for the first layer to completely dry before scraping the second layer, otherwise the two layers of putty may not adhere firmly. The focus of the second pass is to "find the details", filling in the small flaws and scratches left by the first pass to make the overall wall smooth and even.

　　第二遍膩子干透后，就到了決定墻面手感的打磨環節。建議用240-320目的細砂紙，打磨時要順著光線輕輕磨，還要勤用靠尺檢查平整度，避免打磨出波浪紋。打磨完成后，一定要用雞毛撣或吸塵器把墻面和地面的粉塵徹底清理干凈，粉塵沒清干凈就刷漆，很容易導致漆面起砂、脫落。

　　After the second coat of putty dries, it's time for the polishing process that determines the texture of the wall. It is recommended to use 240-320 grit fine sandpaper. When polishing, gently polish along the light and frequently use a ruler to check the flatness to avoid creating wavy patterns. After polishing, be sure to thoroughly clean the dust on the walls and floors with a chicken feather duster or vacuum cleaner. Brushing the paint without cleaning the dust can easily cause sanding and peeling of the paint surface.

　　最后是刷漆收尾，粉塵清理干凈后先刷一遍底漆。底漆能起到封固防潮的作用，還能提升面漆的附著力，千萬別省略。底漆干透后再刷兩遍面漆，每遍面漆之間要間隔4-6小時，刷的時候要均勻涂抹，避免出現流掛、刷痕等問題。

　　Finally, the painting is done, and after cleaning up the dust, a coat of primer is applied first. Primer can play a role in sealing and moisture-proof, and can also enhance the adhesion of topcoat. Do not omit it. After the primer is completely dry, apply two coats of topcoat, with an interval of 4-6 hours between each coat. Apply evenly during brushing to avoid problems such as sagging and brush marks.

　　還要提醒大家兩個施工注意事項：一是施工時要控制室內濕度，潮濕天氣盡量別施工，不然膩子難干透，后期容易發霉；二是膩子要選優質耐水款，尤其是廚房、衛生間周邊的墻面，耐水膩子的耐用性更強。其實膩子粉使用沒什么復雜的技巧，只要把調制的細節把控好，施工流程一步不落地做好，就能避免大部分問題，讓墻面長久保持平整美觀。

　　Two construction precautions need to be reminded: first, control indoor humidity during construction, and avoid construction in humid weather as much as possible, otherwise the putty will be difficult to dry completely and prone to mold in the later stage; Secondly, high-quality water-resistant putty should be selected, especially for walls around kitchens and bathrooms, as water-resistant putty has stronger durability. In fact, there are no complicated techniques for using putty powder. As long as the details of the mixing are well controlled and the construction process is completed step by step, most problems can be avoided, and the wall can be kept flat and beautiful for a long time.

　　本文由  濟南膩子粉   友情奉獻.更多有關的知識請點擊  http://www.zzmdwxsh.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan Putty Powder For more related knowledge, please click http://www.zzmdwxsh.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.